Target accuracy on LWR neutronics parameters is 2 to 5 times lower than the a priori uncertainty (1σ)
due to nuclear data. This paper summarizes the experimental facilities and the integral measurements that are required
for code qualification. The rigorous use of integral information through trend analysis method is described. Trends
on JEF2 data from Keff measurements and P.I.Es are presented. These trends were accounted for in the new JEFF3
evaluations. The role of fundamental experiments, such as worth measurement of separated isotopes, is emphasized.

This paper presents an evaluation of the amount of burnup credit needed for high-density casks to
transport the current U.S. inventory of commercial spent nuclear fuel (SNF) assemblies. A prototypic
32-assembly cask and the current regulatory guidance were used as bases for this evaluation.
By comparing actual pressurized-water-reactor (PWR) discharge data (i.e., fuel burnup and initial
enrichment specifications for fuel assemblies discharged from U.S. PWRs) with actinide-only-based

This publication records the proceedings of a technical meeting organized by the IAEA and
held in London 29 August–2 September 2005 with sixty participants from 18 countries. As
indicated in the title, the objective of this meeting was to provide a forum for exchange of
technical information on spent fuel burnup credit applications and thereby compile state-ofthe-
art information on technical advances related to spent fuel transportation, storage,
reprocessing and disposition.

The Interim Staff Guidance on burnup credit (ISG-8) for spent fuel in storage and transportation casks, issued by the Nuclear Regulatory Commission’s Spent Fuel Project Office, recommends a burnup measurement for each assembly to confirm the reactor record and compliance with the assembly burnup value used for loading acceptance. This recommendation is intended to prevent unauthorized loading (misloading) of assemblies due to inaccuracies in reactor burnup records and/or improper assembly identification, thereby ensuring that the appropriate subcritical margin is maintained.

Presented at the NEI Used Fuel Management Conference, St. Petersburg, FL, May 7-9, 2013

The objective of this calculation is to evaluate the required minimum burnup as a function of initial boiling water reactor (BWR) assembly enrichment that would permit loading of spent nuclear fuel into the 44 BWR waste package configuration as provided in Attachment IV. This calculation is an application of the methodology presented in ''Disposal Criticality Analysis Methodology Topical Report'' (YMP 2003). The scope of this calculation covers a range of enrichments from 0 through 5.0 weight percent (wt%) U-235, and a burnup range of 0 through 40 GWd/MTU.

The purpose of this document is to summarize the degraded waste package disposal criticality evaluations which were reported in FY 1997 (Refs. 2-6), and to explain how those evaluations have served to further develop various aspects of the overall methodology for such evaluations.

This technical work plan (TWP) describes the planning of burnup credit (BUC) experimental work to be implemented by the U.S. Department of Energy (DOE) Office of Civilian Radioactive Waste Management (OCRWM) Lead Laboratory for Repository Systems. This TWP serves to coordinate and integrate a program to implement Work Packages S31023 to S31036 of the fiscal year 2007 annual work plan (AWP) for the Lead Laboratory.

The purpose of this activity is to develop a representative “limiting” axial burnup profile for pressurized water reactors (PWRs), which would encompass the isotopic axial variations caused by different assembly irradiation histories, and produce conservative isotopics with respect to

Disposal Criticality Analysis Methodology Topical Report1 describes a methodology for performing postclosure criticality analyses within the repository at Yucca Mountain, Nevada. An important component of the postclosure criticality analysis is the calculation of conservative isotopic concentrations for spent nuclear fuel. This report documents the isotopic calculation methodology. The isotopic calculation methodology is shown to be conservative based upon current data for pressurized water reactor and boiling water reactor spent nuclear fuel.

The Materials Characterization Center (MCC) at Battelle Pacific Northwest Laboratory (PNL) has the responsibility to select appropriate spent fuel Approved Testing Materials (ATMs) and to characterize, via hot-cell studies, certain detailed properties of the discharged fuel. The purpose of this report isto develop a collective description of the entire spent fuel inventory in terms of various fuel properties relevant to ATMs using information available from the Characteristics Data Base (CDB), which is sponsored by the U.S.

The work reported here is an investigation of the sensitivity of component temperatures in a specific storage system, including fuel cladding temperatures, in response to modeling assumptions that differ from design-basis, including age-related changes that could degrade the thermal behavior of the system. Preliminary evaluations of representative horizontal and vertical storage systems at design basis conditions provides general insight into the expected behavior of storage systems over extended periods of time.

The objectie of this calculation is to document the Grand Gulf, Unit 1, (GG1) fuel depletion calculations. The GG1 reactor is a boiling water reactor (BWR) owned and operated by Entergy Operations Inc. The Commercial Reactor Criticality (CRC) evaluations support the development and validation of the neutronic models used for criticality analyses involving commercial spent nuclear fuel in a geologic repository. This calculation is performed as part of the evaluation CRC program. This report is an engineering calculation supporting the burnup credit methodology of YMP 2000 (Ref.

<div class="page" title="Page 1">
<div class="section">
<div class="layoutArea">
<div class="column">

<div class="page" title="Page 2">
<div class="layoutArea">
<div class="column">

<div class="page" title="Page 8">
<div class="layoutArea">
<div class="column">

<div class="page" title="Page 1">
<div class="layoutArea">
<div class="column">

Analytical methods, described in this report, are used to
systematically determine experimental fuel sub-batch
reactivities as a function of burnup. Fuel sub-batch reactivities
are inferred using more than 600 in-core pressurized water
reactor (PWR) flux maps taken during 44 cycles of operation
at the Catawba and McGuire nuclear power plants. The
analytical methods systematically search for fuel sub-batch
reactivities that minimize differences between measured and
computed reaction rates, using Studsvik Scandpower’s

The concept of direct disposal of dual-purpose canisters (DPCs) has not been previously considered
for the Yucca Mountain geologic repository because of concerns, among other reasons,
about degradation of the reactivity-control material over the relatively long period of the repository
analyses. Aluminum-based neutron absorber materials, typically used in DPCs, are not
expected to have sufficient corrosion resistance necessary to retain their integrity over a 10,000+

Title 10 of the Code of Federal Regulations (10 CFR) Part 71, Packaging and Transportation of
Radioactive Material, and 10 CFR Part 72, Licensing Requirements for the Independent
Storage of Spent Nuclear Fuel, High-Level Radioactive Waste, and Reactor-Related Greater
Than Class C Waste, require that spent nuclear fuel (SNF) remain subcritical in transportation
and storage, respectively. Unirradiated reactor fuel has a well-specified nuclide composition
that provides a straightforward and bounding approach to the criticality safety analysis of

Progress toward developing a technical basis for a cost-effective burnup credit methodology for
spent nuclear fuel with initial U-235 enrichment up to 5% is presented. Present regulatory
practices provide as much burnup credit flexibility as can be currently expected. Further progress
is achievable by incorporating the negative reactivity effects of a subset of neutron-absorbing
fission product isotopes. Progress also depends on optimizing the procedure for establishing the

In 1999, the United States Nuclear Regulatory Commission (U.S. NRC) initiated a research program
to support the development of technical bases and guidance that would facilitate the implementation of burnup
credit into licensing activities for transport and dry cask storage. This paper reviews the following major areas of
investigation: (1) specification of axial burnup profiles, (2) assumption on cooling time, (3) allowance for
assemblies with fixed and removable neutron absorbers, (4) the need for a burnup margin for fuel with initial

The objective of this calculation is to provide the uncertainty term for fission product and minor actinides which contributes to the determination of the critical limit for burnup credit calculations. The scope of this calculation covers PWR and BWR spent nuclear fuel. This activity supports the Criticality Department's validation of burnup credit. The intended use of these results is in future Criticality Department calculations and analyses.